The Trigger Supply AR-10 Super Safety Lever is the missing piece that brings the Hoffman Tactical Super Safety active reset system to your AR-10 platform. Machined from S7 shock-resistant tool steel with a dual-fin tip, this lever replaces the AR-15 lever in your existing Super Safety kit — your cam, selector, cam pin, and trigger all carry over unchanged. This is the lever only.
Compatible with DPMS Gen 1, DPMS Gen 2, Armalite, and SR-25 pattern AR-10 platforms. Due to tolerance variation across AR-10 manufacturers, minor gunsmithing may be required for proper fitment.
This is not a guaranteed plug-and-play install. AR-10 platform tolerances vary significantly across manufacturers. Minor gunsmithing — light fitting, polishing, or small material removal — may be required to achieve proper fitment and reliable function. Installation by a qualified gunsmith familiar with AR-10 platforms is strongly recommended. If you are not comfortable with minor fitting work, have a gunsmith install this component.
What Carries Over — What Doesn't
If you already own an AR-15 Super Safety, you have most of what you need. Only the lever is AR-10 specific.
Super Safety cam · Selector · Cam pin · Trigger (pre-cut curved)
Lever — dual-fin tip, S7 tool steel, AR-10 geometry
You will need a complete Super Safety kit in addition to this lever. See the full Super Safety lineup — the S7 curved trigger kit is the recommended pairing for this AR-10 lever.
Why S7 Tool Steel — Why It Matters for the Lever
The lever is the hardest-working component in the Super Safety system. On every cycle, the BCG contacts the lever and drives it — and through it, the trigger — forward. That is a shock load on every single round fired. Most levers run in standard tool steel. This one doesn't.
- Highest impact toughness of any tool steel grade — S7 is engineered specifically for shock loads. The cam absorbs the BCG impact; the lever transfers that force to the trigger. S7 handles that stress better than any other tool steel available
- Wear surfaces hold their geometry — consistent reset timing over tens of thousands of rounds where standard steel shows wear and begins to affect reset reliability
- Dual-fin tip design — two contact points on the trigger interface provide more reliable and consistent trigger engagement across the wider tolerance range of AR-10 platform variants
- Tighter machining tolerances — S7 machines cleanly to tighter specs, meaning a more precise lever geometry from the start
Compatible AR-10 Platforms
Minor gunsmithing may be required depending on your specific manufacturer's tolerances. Not compatible with AR-15 lowers — this lever is AR-10 geometry only.
Specs
| Material | S7 Shock-Resistant Tool Steel |
| Tip Design | Dual-Fin |
| Compatible Platforms | DPMS Gen 1, DPMS Gen 2, Armalite, SR-25 pattern AR-10 |
| Carries Over From AR-15 Kit | Super Safety cam, selector, cam pin, curved trigger |
| Kit Contents | Lever only |
| Installation | May require minor gunsmithing — qualified installer recommended |
| Brand | Trigger Supply |
| Country of Origin | USA |
Frequently Asked Questions
What AR-10 platforms is this compatible with?
What parts from my AR-15 Super Safety carry over?
Is this a plug-and-play install?
What is the dual-fin tip design?
Why S7 tool steel for the lever?
Do I need a complete Super Safety kit or just this lever?
Related Products
- All Super Safety Products — Complete Kits & Components
- Trigger Supply Super Safety S7 Curved Trigger ($99.99)
- Trigger Supply Super Safety S7 Flat Trigger ($119.99)
- Trigger Supply AR-15 Anti-Walk Pins ($24.99)
- FRT vs Super Safety — Full Comparison
- Are FRT Triggers Legal? — State-by-State Guide
Minor gunsmithing may be required for proper fitment due to tolerance variation across AR-10 platform manufacturers. Installation by a qualified gunsmith familiar with AR-10 platforms is strongly recommended. It is the buyer's responsibility to verify compatibility with their specific host platform and to comply with all applicable local, state, and federal laws. Trigger Supply is a brand of TTT Innovations.
The AR-Takedown Tool (AR-TT)
- weight is only 58 grams, under 3oz
-Length: 6 5/16"
-Diameter 1/2"
-This is the ONLY USA made gun smithing tool, gun cleaning tool, building tool, disable tool on the market.