A black compact submachine gun, kriss vector, with a vertical foregrip and a mounted optic on a plain white background.
Trigger Supply Kriss Vector FRT Trigger
Kriss_Vector_frt-trigger-forced reset for your vector
Kriss vector FRT
Kriss Vector FRT — Forced Reset Trigger | All Gens & Calibers

Kriss Vector FRT — Forced Reset Trigger | All Gens & Calibers

$149.99 $169.99
Tax included.
A black compact submachine gun, kriss vector, with a vertical foregrip and a mounted optic on a plain white background.

Kriss Vector FRT — Forced Reset Trigger | All Gens & Calibers

$149.99 $169.99
Information

 

 

 

Now included: the 3-position selector cam. Every Kriss Vector FRT now ships with a 3-position selector cam at no extra cost. Swap it in for the factory cam and your Vector runs Safe, Semi and FRT on the factory selector levers, so you get a true semi-auto position as well as forced reset. Already own an earlier kit? Get the Kriss Vector 3-Position Selector Cam on its own.

Compatibility

Gen 2 Gen 2.1 Gen 3 .45 ACP 10mm .40 S&W 9mm
⚠ Gen 1 owners: Gen 1 Vector requires a Gen 2 trigger pack — KRISS Vector Fire Control Group (Semi) — before this FRT can be installed.

Overview

A stainless steel, 2-position drop-in Forced Reset Trigger for the Kriss Vector. This upgrade enhances firing performance to deliver rapid cycling as intended by the original designers. It is a forced reset device and not a full-auto conversion. Proper operation requires controlled trigger input.

Our blog includes installation guidance for the Kriss Vector FRT for optimal performance. Our gunsmith team is also available to assist remotely with installation and function checks.

Looking for an AR-15 FRT instead? See our full best FRT triggers for AR-15 guide or shop the Partisan Disruptor FRT.

Disclaimer

  • This is an aftermarket component. The user assumes all liability for damage or injury.
  • Excessive lubrication is required during initial use.
  • This is not a permanent modification — parts will wear and require replacement over time.
  • Warranty replacements may be provided upon approval.
  • Ensure firearm is properly broken in before installation.

Break-In & Pre-Installation

The Kriss Vector platform requires a break-in period of approximately 350+ rounds and may exhibit issues prior to modification. Before installing this FRT, perform the following:

  • Polish bolt lugs (ears) to a smooth finish
  • Polish the FRT after fitting
  • Polish action rail guides
  • Thoroughly clean the firearm to ensure smooth cycling

Installation Steps

  1. Separate the lower and upper receiver halves.
  2. Remove optics or iron sights.
  3. Remove the top rail (roll pin and Allen screw for Gen 1).
  4. Slide off the top rail from stock to muzzle.
  5. Remove fire control group screws and extract the assembly.
  6. Remove trigger and disconnect.
  7. Install the FRT and perform initial test fit.
  8. Function check manually for any hangups.
  9. Remove and polish any contact points causing resistance.
  10. Reinstall and function check again.
  11. Manually actuate hammer and trigger to confirm reset.
  12. Repeat polishing if necessary.
  13. Reassemble firearm and apply lubrication (high-temp grease or ATF4 recommended).
Function check: After assembly, manually cycle the action and pull the trigger to confirm reset pressure and smooth operation. If resistance is present, repeat polishing and cleaning steps.

Test Fire Procedure

  1. Load 1 round — verify bolt locks back.
  2. Load 2 rounds — test cycling.
  3. Load 3 rounds — confirm reliability.
  4. Full magazine — verify full performance.

If issues occur during testing, return to polishing, lubrication, and inspection steps.

Support

If you experience issues, contact customer service before attempting advanced troubleshooting procedures.

Fitment variations may cause hangups. Polishing can be done manually or with tools, including tumbling if necessary. High-temp grease or ATF4 lubrication is recommended throughout.

Related Products & Resources

    What's in the Box

    • (1) Kriss Vector FRT, stainless steel drop-in
    • (1) 3-position selector cam (Safe / Semi / FRT), high-density polymer

    Kriss Vector FRT FAQ

    Does the Kriss Vector FRT come with a 3-position selector?

    Yes. Every Kriss Vector FRT now ships with a 3-position selector cam at no extra cost, giving you Safe, Semi and FRT on the factory selector levers.

    Which Kriss Vector generations and calibers does this FRT fit?

    It fits Gen 2, Gen 2.1 and Gen 3 Vectors in 9mm, .40 S&W, 10mm and .45 ACP. Gen 1 Vectors need the Gen 2 trigger pack installed first.

    I bought an earlier kit without the selector. Can I add it?

    Yes. The 3-position selector cam is sold on its own for $29.99 and drops into earlier kits on Gen 2, Gen 2.1 and Gen 3 Vectors.

  • Partisan Disruptor FRT — AR-15 Forced Reset Trigger
  • Odin Works HFRT Buffer System — Purpose-Built for FRTs
  • NSPEC Innovations 10/22 FRT — Ruger 10/22 Forced Reset Trigger
  • Partisan Disruptor FRT + Odin Works HFRT Bundle — Save $30
  • Hoffman Tactical Super Safety
  • AS Designs ARC-Fire V2

FRT Resources

Product reviews

Customer Reviews

Overall rating: 3.6 / 5 from 9 reviews.

My gun is currently at a shop getting rebuilt because the trigger doesn’t even shoot thanks to this garbage trigger never buying from here again. What a great way to waste 150$ and now I have to pay labor to fix a brand new 2000$ gun

Kriss Vector FRT — Forced Reset Trigger | All Gens & Calibers